Search results

  1. A

    Sureflo pump setup!

    Hi Scott When we set ours up we used a quick connect that would allow us to use any of our PW guns. Last week we used it to spray stripper on a elevated deck through our extention wand. After letting it set we used it to spray the 2x12s off and the outer side of the spindles. Worked great...
  2. A

    Shotgun mold

    Hi Mike Good to hear from you. We are going to pass on this job. It has been on it for about 4yrs... I will refer him to the low- baller in my area. Let him have the headaches. Talk to you later and thanks again for the info Mike. I did go to a site that explained about it last yr but...
  3. A

    Shotgun mold

    Hi Ya all Has anyone yet found a quick way of removing shotgun mold ? I have a potential custom that has it .I plan on going out sometime next week to look at it. From what he has described it is pretty bad even on the soffitts. Thanks again for the help. Tim
  4. A

    Sealers for docks on water

    Hi again we have a customer who wants a deck sealed and also a dock that goes into a lake cleaned and sealed. What type of sealer would you want to use by the water? Wondering about EPA? How do you keep drips out of the water? Thanks Tim
  5. A

    Question about CWF

    Hi All I have a deck that I am quoting that is currently suppose to sealed with Cwf 2 yrs ago. Suprisingly it is still in good shape. I believe mostly because of the shade that it is in. After looking at it I do not feel that it should be completely stripped only cleaned and touched up with...
  6. A


    Say Jon Did you say that you get the industrial stripx in a powder form or a liquid? I have oly found it in the liquid form it almost looks like red jello before it is diluted. I dave had pretty good luck with it though. I was not able to use it on latex though. Have you ever tried it on a latex...
  7. A

    Anyone run 2 guns on their unit?

    I have a 3500psi 5.5 gpm hot water Elite skid unit. I want to put a tee in the discharge hose to hookup 2 guns one for my extention and one for my 6ft lance (lower) level gun. Question is will the ocassional use of both guns bother my hotwater unit? Also I know that the pressure will drop in 1/2...
  8. A

    CWF info needed

    Hi everyone. I just got a call for a estimate bid on cleaning a large deck with cwf on it. He wants to recoat it if possible. Has anyone used it before? If so how hard is it to apply? Another question is this sealer easy or hard to strip? It is approx about 1yr old. Thanks for the help. Tim...
  9. A

    Any one ever use a PW gun and QC tips to apply sealer?

    HI Rick I did get a QC gun handle on the chem sprayer. Now I am playing with different size nozzles. I want one for spindles and one for flat work. Ordered some today hope they work. Tim ------------------ Tim Highfield ALL-BRITE POWERWASHING
  10. A

    Two/Three Story House

    We have both the xjet /w the soap nozzle and we also use extention wands along with the xjet for those 3 story homes. But we always still brush some areas. As you know each job is a little different. But stick to your prices and do quality work. Just my 2 cents worth. Tim...
  11. A

    Injector problem

    Thanks guys When all else fails I use the xjet it sure puts the soap on quick. Just hate dragging around the bucket. I also ordered a larger soap nozzle tip . So we will see if combined with the new injector maybe it will do the job. I need to post a picture of my new trailer it is really...
  12. A

    Injector problem

    Hi Guys I am setting up my new unit and have a problem not pulling any soap from chem tank. I believe that the 200ft of high pressure is causing too much resistance or ristriction to create the venturi action that I need. I am running a 5.5gpm unit with 3000psi and 200ftof hose. I tried a...
  13. A

    Residential water supply

    We just did a commercial job for a new water treatment plant. I went with an empty tank. It took me 45 min to get 1/2 of my water tank full.And I emptied it in 20 min. So I do like Mike I normally go with a full tank then hook up to their water if I think that I will use more water. I just did a...
  14. A

    Problem with chem injector

    I have a problem not getting soap from the chem tank. Here is a dumb question. Are your soap nozzles sized according to the press and gpm? I am now using a 5.5gpm instead of a 4gpm. The soap will come out if I use no nozzle. Is it the injector? Any suggestions ? Thanks...
  15. A

    Any one ever use a PW gun and QC tips to apply sealer?

    Hi Guys I am thinking about building my own sealer sprayer. I have a 1.5gpm 60psi sureflo pump and was wondering if I could attach a Pw gun and quick connect nozzles to it. The problem would be what nozzle size should I use. Since Ready Seal is quite thin I figured about a 1.5 or 2gpm nozzle but...
  16. A

    Orlando - You Gonna Be There?

    Sorry Dave not this time I am going to start saving my pennys for the cruise. Tim ------------------ Tim Highfield ALL-BRITE POWERWASHING
  17. A

    Need a good rust remover for white vinyl house!

    Looking for a good rust remover to remove the hard water from the sprinkler system on a white vinyl house. They want it washed next week if possible. Sure hope it does not snow. It will be my first house wash this winter. Sure glad I have a hot water unit. Thanks again Tim ------------------...
  18. A

    Hi pressure pulses

    Thanks Guys we will check it out tomarrow. Tim ------------------ Tim Highfield ALL-BRITE POWERWASHING
  19. A

    Simple green and Dawn Dishwashing liquid?

    Jamie I just bought 2- 55gal mixs of a Delimonene citrus base cleaner that we use for $55 per 55gal mix. Let me know if I can be of any more help. Tim ------------------ Tim Highfield ALL-BRITE POWERWASHING
  20. A

    Hi pressure pulses

    I have a brand new Elite H/c Water unit. 5gpm 3000psi Bypassing to water tank. When I use a 0deg nozzle I get 5secs of high press and about 15 secs of low press. When I used a 40deg nozzle it seemed to work ok. I do not think that I am starving for water . Could the unloader need adjusting? I...