Search results

The white wire is an auxillary 12volt supply. It is used primarly for running an electric fuel pump. HI-Pressure Daren

Dave, Since this system is located in Seattle we installed a oil to water heat exchanger. This system is installed in a 1998 Ford 750 enclosed truck with diesel engine. Anytime they run the truck or plug it in for cold weather the hydrualic oil is preheated. It works well and the...

GLenn, I have never used the electric clutch driven pumps. It is the same type of clutch that lawn tractors use and they hold up for many years. We have built several hydraulic driven units that can consist of as many pumps as you desire and can afford. The last unit I built...

Not the greatest at telling jokes but gave it a try. Man decideds he needs a good guard dog so he goes down to the local pound. He goes to the first cage and hears the meanest looking German Shepard growling at him. He comments to the keeper "Thats one mean dog and I will take him"...

Hey All, Working on a guys home owner unit. I need to know how much oil to put into the pump crankcase. This pump is no longer available and Giant doesn't seem to want to help. So if anyone has any info please help! Daren

Is this pressure washer a direct drive unit. If it is remove the pump from the engine crankshaft and check for key wear. Alot of times it will destroy the pump shaft and the engine crankshaft. You can have a machine shop cut a new keyway in the crankshaft of the engine. This will make a knocking...

Always looking for help in answering any questions. Most of the time everone ends up answering there own question. Always looking for new and better ways to fix and or repair equipment. So join in and help anytime! Daren

I prefer to install the gages in the extra pressure port of the pump, tee before unloader, or with a valve cap adapter. If you install the gage after a unlaoder it will always read pressure and will not show you what the pump is doing: if the unloader is working or not. Hope this helps...

HANNAY

[boing] Like Mark and Wiz said it would be much better to get the oil at the right level. Have seen several seals ruined because of too much oil. Some of those pumps are a bear to get the oil out of so we made a vacuum tank to suck the oil from the pump. We use it all the time to change...

Dan, Briggs uses a very cheap starter solenoid. They do crazy things sometimes. We replace them with a automotive type found on older ford vehicles. Once this is done we never see them back. Also check to make sure your battery connections are tight and pull keyswitch out and check to...

Jon, Like Mark stated you probably have a swivel leaking by. This will lower the pressure at the nozzles. Also you might have bad bearings. They might feel ok when you spin it by hand but when you have 3000psi at the swivel it might cause the swivel to drag. Are you getting a lines as...

Hey Cody, What the wiz is trying to tell ya is 99% of all high pressure nozzles and tips are sized at 4000psi. If you go by the tip chart a #2.5 nozzle will flow 2.5gpm at 4000psi. At 3000psi the same tip will flow around 2.17gpm. So make sure you size the tip for the pressure you are...

Is this a vanguard or is it an I/C opposed twin. Does it only have one coil? If it is an opposed twin it will not have diodes on the kill wire. Also most of the opposed twins do have a fuel pump that does fail. They are sometimes mounted on the engine cowl or built into the carb. Can't remember...

<FONT size="6">MORE POWER!!!!!!!!!!!!</FONT s> As long as the pump is turning the correct rpm you can basically install any motor or engine on it. Daren Marshall ------------------

Hey All, I was over at Pep-Boys about a week ago and found a remote control for fog lights. With my discount the price was $23.98. Normal cost on it is $29.99. It is made by Rally. The range seems to be about 150ft. It has a 30amp latching relay built in so no need to add. It is only one...

Is the pump feel like it is pulsating? Sounds like its sucking air still. Make sure all the connections are tight and leak free. Could you give us a description of the type of injector it has. Is it ajustable? Also make sure your chemical hose has a wieght on it so it doesn,t curl up out of the...

Does the unit sound like it is trying to build pressure? Have you unhooked everything back to the pump to make sure you have good water flow. Kinda sounds like an obstruction or a restriction on the supply side. Daren Marshall HI-Pressure ------------------

We use either a 40 or 50 mesh screen on the filter at the tank. Daren Marshall HI-Pressure ------------------

Just want to say sorry for not being here as often as needed. Our 1 year old daughter has recently went thru a major open heart surgery and we have been very busy taking care of family. She is doing fine and I hope that I can spend more time on the board. Thank you, Daren Marshall HI-Pressure...